CUET PG PYQs for Measurement of voltage with Solutions: Practice CUET PG Previous Year Questions

Content Writer | Journalism Graduate | J/hVSQ

Measurement of voltage is an important topic in the Electrical and Electronic Measurements section in CUET PG exam. Practising this topic will increase your score overall and make your conceptual grip on CUET PG exam stronger.

This article gives you a full set of CUET PG PYQs for Measurement of voltage with explanations for effective preparation. Practice of CUET PG Electrical and Electronic Measurements PYQs including Measurement of voltage questions regularly will improve accuracy, speed, and confidence in the CUET PG 2026 exam.

CUET PG PYQs for Measurement of voltage with Solutions

1.
The overall gain \(\frac{C(S)}{R(S)}\) of the block diagram shown below is
- \(\frac{G_1G_2}{1-G_1G_2H_1H_2}\)
- \(\frac{G_1G_2}{1-G_2H_2-G_1G_2H_1}\)
- \(\frac{G_1G_2}{1+G_2H_1+G_1G_2H_2}\)
- \(\frac{G_1G_2}{1-G_1G_2H_1-G_1G_2H_1}\)
View Solution
2.
What is the maximum output voltage of a 3-ph bridge rectifier supplied with line voltage of 440V?
- 528V
- 396V
- 594V
- 616V
View Solution
3.
Given below are two statements:
Statement I: The speed of an induction motor can not be continued as easily and efficiently as that of a de shunt motor.
Statement II: Slip of an induction motor can not be changed by varying the voltage applied to the stator
- Both Statement I and Statement II are true
- Both Statement I and Statement II are false
- Statement I is true but Statement II is false
- Statement I is false but Statement II is true
View Solution
4.
PIV of a SCR is 650V. Find out the required Voltage if the safety factor is 2.
- 230.4 Volt
- 232 Volt
- 300 Volt
- 320 Volt
View Solution
5.
An Op-amp has a slew rate of 5V/us. The largest sine wave output voltage possible at a frequency of 1MHz is____
- \(10\pi V\)
- 5V
- \((5/ \pi )V\)
- \((5/2 \pi)V\)
View Solution
6.
The circuit shown in the figure will work as____
- Buck-boost converter
- Buck converter
- Boost converter
- Dual converter
View Solution
7.
Assume the incremental cost characteristics of two generates delivering 250MW as.
\(\frac{dF_1}{dP_1} = 20 +0.01P_1\)
\(\frac{dF_2}{dP_2} = 14 +0.2P_1\)
For economic operation, the generation P₁ and P₂ should be:
- P₁ = P₂ =125MW
- P₁ = 209.5MW; P₂ = 40.5MW
- P₁ = 250MW; P₂ = 0MW
- P₁ = 40.5MW; P₂ = 209.5MW
View Solution
8.
The classification of transmission lines (T.L)as short. Medium & Long T.L is based upon__
- Nominal Voltage of the line
- Physical length of the line
- Wave length of the line
- Power Transmitted over the line
View Solution
9.
Which displacement transducer is used for accurate and linear measurement?
- LVDT
- Strain gauge
- Potentiometer
- Capacitive displacement transducer
View Solution
10.
A 0 to 200V Voltmeter has a accuracy of 1% of full scale reading. The voltage measure by this instrument is 50V. What is limiting error?
- 4%
- 2%
- 1%
- 0.25%
View Solution
11.
The maximum possible speeds in rpm at which an alternators can be driven to generate voltages at 60 Hz and 50 Hz are, respectively:
- 7200, 6000
- 3000, 3600
- 6000, 7200
- 3600, 3000
View Solution
12.
A buck regulator has an input voltage of 16V and the required output voltage is 4V. What is the duty cycle of the regulator?
- \(\frac{1}{16}\)
- \(\frac{1}{8}\)
- \(\frac{1}{4}\)
- \(\frac{3}{4}\)
View Solution

View more CUET PG Questions

gr54sW uqE+cS

Comments

No Comments To Show

CUET PG PYQs for Measurement of voltage with Solutions

1.The overall gain \(\frac{C(S)}{R(S)}\) of the block diagram shown below is

2.What is the maximum output voltage of a 3-ph bridge rectifier supplied with line voltage of 440V?

3.Given below are two statements:Statement I: The speed of an induction motor can not be continued as easily and efficiently as that of a de shunt motor.Statement II: Slip of an induction motor can not be changed by varying the voltage applied to the stator

4.PIV of a SCR is 650V. Find out the required Voltage if the safety factor is 2.

5.An Op-amp has a slew rate of 5V/us. The largest sine wave output voltage possible at a frequency of 1MHz is____

6.The circuit shown in the figure will work as____

7.Assume the incremental cost characteristics of two generates delivering 250MW as.\(\frac{dF_1}{dP_1} = 20 +0.01P_1\)\(\frac{dF_2}{dP_2} = 14 +0.2P_1\)For economic operation, the generation P1 and P2 should be:

8.The classification of transmission lines (T.L)as short. Medium & Long T.L is based upon__

9.Which displacement transducer is used for accurate and linear measurement?

10.A 0 to 200V Voltmeter has a accuracy of 1% of full scale reading. The voltage measure by this instrument is 50V. What is limiting error?

11.The maximum possible speeds in rpm at which an alternators can be driven to generate voltages at 60 Hz and 50 Hz are, respectively:

12.A buck regulator has an input voltage of 16V and the required output voltage is 4V. What is the duty cycle of the regulator?

Comments

dOGVmW

1.
The overall gain \(\frac{C(S)}{R(S)}\) of the block diagram shown below is

2.
What is the maximum output voltage of a 3-ph bridge rectifier supplied with line voltage of 440V?

3.
Given below are two statements:
Statement I: The speed of an induction motor can not be continued as easily and efficiently as that of a de shunt motor.
Statement II: Slip of an induction motor can not be changed by varying the voltage applied to the stator

4.
PIV of a SCR is 650V. Find out the required Voltage if the safety factor is 2.

5.
An Op-amp has a slew rate of 5V/us. The largest sine wave output voltage possible at a frequency of 1MHz is____

6.
The circuit shown in the figure will work as____

7.
Assume the incremental cost characteristics of two generates delivering 250MW as.
\(\frac{dF_1}{dP_1} = 20 +0.01P_1\)
\(\frac{dF_2}{dP_2} = 14 +0.2P_1\)
For economic operation, the generation P₁ and P₂ should be:

8.
The classification of transmission lines (T.L)as short. Medium & Long T.L is based upon__

9.
Which displacement transducer is used for accurate and linear measurement?

10.
A 0 to 200V Voltmeter has a accuracy of 1% of full scale reading. The voltage measure by this instrument is 50V. What is limiting error?

11.
The maximum possible speeds in rpm at which an alternators can be driven to generate voltages at 60 Hz and 50 Hz are, respectively:

12.
A buck regulator has an input voltage of 16V and the required output voltage is 4V. What is the duty cycle of the regulator?